Rotating Equipment Design,Selection&Installation Workshop

DEVELOP Training Center menyelenggarakan Kelas Rotating Equipment Design,Selection&Installation Workshop yang sangat berguna untuk mendapatkan skill tentang Rotary Equipments pada proyek&operation Oil,Gas,Geothermal,Power Plant&Petrochemical, seperti diantaranya:

• Rotating Equipment Design
• Rotating Equipment Selection
• Mechanical Vendor Document Review untuk Rotating Equipment
• FAT/Factory Acceptance Test Rotating Equipment Procedure
• SAT/Site Acceptance Test Rotating Equipment Procedure
• Rotating Equipment Installation&Operational Test Procedure

Selama training, instruktur kami akan menggunakan kombinasi teori serta praktek langsung dengan studi kasus yang telah dipersiapkan yang menyerupai Proyek nyata.

Rotating Equipment Design,Selection&Installation

DEVELOP menerapkan Syllabus Training Rotating Equipment Design,Selection&Installation Workshop dengan tahap-tahap pembelajaran berkualitas sbb :

Sesi 1-2

Skill Focus:

• Rotating Engineers Fundamental
• Rotating Engineers Applicable Standard&Codes
• Rotating Engineers Scope of Works in Projects & Plant Operation
• Mechanical System
  • Pump&Compressor Drivers
  • Pump Classifications
  • Centrifugal Pump Performance Curves
  • Compressor Types
• Reciprocating Compressors
  • Principle of Operation
  • Single Acting Trunk Piston
  • Double Acting Crosshead
  • Compression Cycle
  • Pressure,Suction,Volume&Discharge
• Reciprocating Compressors Main Components
  • Pulsation Bottles,Crankcase Cast Iron&Crankshaft Forged Steel
  • Counterweight for balancing
  • Crosshead Cast Steel
  • Ballast for balancing of inertia forces
  • Pneumatic Valve Unloaders for capacity control
  • Main Oil Pump,Connecting Rod forged steel&Oil Wiper Packing
  • Piston Rod&Rod Packing
  • Cylinder Valve
• Rotary Screw Compressor
  • Oil-Free&Oil-injected
  • Dynamic Compressors
  • Centrifugal&Axial
  • Centrifugal for compressing natural gas
  • Axial for compressing air for gas turbine driving centrifugal compressor
• Centrifugal compressors
  • Single stage (diffuser)
  • Multi-stage
• Centrifugal vs. Reciprocating Compressors
• Rotating Equipment Design,Selection&Installation CASE STUDY

Sesi 3-4

Skill Focus

• Turbines & Turboexpanders
  • Turboexpander Cutaway
  • Expander Compressor Cross Section with Thrust Balancing
• Gas Turbine Engine
  • Gas Turbine Engine Principle of Operation
  • Gas Turbine Coupled to CentrifugalCompressor
  • Combustion Turbine
• Industrial Gas Turbines
• Gas Turbine Engines Specification (Power Rating-Heat Rate-Pressure Ratio-Power Shaft)
• Heat rate
  • Reciprocal of the thermal efficiency
  • Adiabatic & mechanical efficiencies
  • Fuel Gas
  • Combustion Chamber
  • Exhaust Gas
  • Axial Compressor
  • Centrifugal Compressor
  • HP/LP Turbine
  • Temperature
  • Ideal Cycle Efficiency
• Reciprocating Compressors
• Propane Refrigeration Compressors
• Propane Compressors with Air-cooled Heat Exchangers
• Reciprocating Compressor at Gas Well
• 2 stage 2,000 HP Reciprocating Compressor
• Oil-Injected Rotary Screw Compressor
• Two-stage screw compressor
• Centrifugal Compressors Issues
  • Pressure Head
  • Surge Line
  • Stonewall Line
  • Inlet Volume Flow
  • Air&Hot Gas Paths
• Rotating Equipment Design, Selection&Installation CASE STUDY

Rotating Equipment Fundamental,Selection,Application&Installation

Materi Training di DEVELOP Training Center dirancang khusus oleh para praktisi designer & engineer sesuai dengan kebutuhan project. Anda akan mendapat sharing ilmu langsung dari para praktisi yang berpengalaman.

Selama training, instruktur kami akan menggunakan kombinasi teori serta praktek langsung dengan studi kasus telah dipersiapkan yang menyerupai Proyek nyata.

QUICK REGISTER :